Direkt zum Hauptinhalt
The Lumafield Trocar Report is available now >
de
en
ja
de
fr
Platform
Branchen
Alle Branchen
Aerospace and Defense
Agriculture and Food
Athletic Equipment
Automotive
Batteries
Consumer Packaged Goods
Electronics
Medical Devices
Applications
Ressourcen
Whitepapers
Ressourcen
Webinare
Parts and Services
Blog
Insights from lumafield
Go/No-Go
Manufacturing podcast
First Article
Editorial Publication
Merchandise Shop
Wear Your Favorite Scans
Firma
Über
Karriere
Drücken
Events
Starten Sie Voyager
Vertrieb kontaktieren
de
en
ja
de
fr
Menü
ProdukteBranchen
Branchen
Alle Branchen
Medical Devices
Electronics
Consumer Packaged Goods
Automotive
Athletic Equipment
Batteries
Agriculture and Food
Aerospace and Defense
Applications
Ressourcen
Ressourcen
Whitepapers
101. OKTOBER
Webinars
Erster Artikel
Go/No-Go Podcast
First Article
Merchandise Shop
Parts and Services
Firma
Firma
Über
Karriere
Drücken
Events
Vertrieb kontaktieren
Starten Sie Voyager
© 2000 Lumafield. All Rights Reserved.
Featured REsource

The Connector Quality Report

An AI-assisted investigation of the electrical connector supply chain

Every measurement came from Lumafield’s Quality Agent. For each of eight connector part numbers, it built an analysis, tested it on a few units, and then ran it on every housing, 1,451 in all. It measured material attenuation, porosity, wall thickness, and shape against a known-good reference. We bought the parts from authorized distributors and AliExpress and scanned them on a Lumafield Triton.

From outside, the open-market housings passed for genuine. Inside, they strayed further from the reference shape on seven of eight part numbers and had thinner walls on four. Even genuine parts from two manufacturers, sold as drop-in replacements for each other, differed in composition and clip design. A continuity test or visual check isn’t built to catch any of this. The report shows where these differences sit and how much can vary under one part number.

Ready to dive into our findings?
Get the Report

17.6 million+

vehicles covered by U.S. recalls naming a connector since 2010

1,451 connectors

scanned and analyzed

805,557 CT slice images

analyzed by Quality Agent

100% accuracy

sorting genuine from open-market units on five part numbers

Every measurement came from Lumafield’s Quality Agent, which built an analysis for each part number, tested it on a few units, and ran it on all 1,451 housings. It measured material attenuation, porosity, wall thickness, and shape against a known-good reference. The study covered eight connector part numbers from authorized distributors and AliExpress, scanned on a Lumafield Triton. Six belong to the DT family and a second manufacturer’s drop-in equivalents, so we could compare one form factor across channels and brands.

From outside, open-market housings looked genuine. Inside, they strayed further from the reference shape on seven of eight part numbers and had thinner walls on four. Even two authorized makers of a drop-in pair differed in composition and clip design. A continuity test or visual check isn’t built to catch these. The report shows how much can vary under one part number.

Get the Report

What the scans showed

Same part number, different material

Open-market housings absorbed X-rays differently from genuine ones under the same part number. On one sealed connector, the difference is consistent with less glass fill than the drawing specifies. That signal alone sorted nearly every unit to its source.

Fewer voids, but bigger ones

On one sealed connector, genuine housings held more voids, but the open-market housings held far larger ones. Which source carried more void volume flipped from one part number to the next, so a single porosity limit would miss some of these patterns.

Locks that were already engaged

Quality Agent flagged open-market housings whose lock reinforcement was already in its final position, which no genuine unit did. On an assembly line, a housing in that state can’t take its terminals without a reset and usually goes to scrap.

Download the Connector Quality Report to discover:

  • How genuine and open-market housings compare across eight connector part numbers on material attenuation, porosity, wall thickness, and deviation from a golden reference.
  • What CT shows about a drop-in pair from two authorized manufacturers, and about mated connectors with their seals in working position.
  • How Quality Agent built and ran an analysis for each part number across 1,451 housings, and where CT fits alongside continuity testing, AOI, CMM, and cross-sectioning.
  • Part-number datasheets with annotated scans and key measurements.

See what automated CT analysis finds inside connectors sold under the same part number.

Versenden Sie niemals ein anderes schlechtes Produkt.

Schützen Sie Ihren Ruf und Ihr Geschäftsergebnis mit einer CT-Inspektion.

Kontaktiere unser Team
den Weg ändern
die Welt macht
alles
Branchen
Aerospace and Defense
Agriculture and Food
Athletic Equipment
Automotive
Batteries
Consumer Packaged Goods
Electronics
Medical Devices
Alle Branchen
Anwendungen
Assembly Verification
Competitive Benchmarking and Analysis
Defect Detection
Design Verification and Validation
Dimensional Measurement
Failure Analysis
First Article Inspection (FAI)
Material Characterization
Non-Destructive Testing (NDT)
Quality Assurance and Control (QA & QC)
Reverse Engineering
Supplier Qualification
All Applications
Produkte
NeptunTritonVoyagerMarsSaturn
Ressourcen
LernenErster ArtikelWhitepapersEreignisseWebinareUnterstützungFallstudien101. OKTOBERBlog der Ingenieure
Firma
EinloggenÜberKarriereDrückenBlogKontakt
de
en
ja
de
fr

Melde dich für unseren Newsletter an

info@lumafield.com
DatenschutzInformationssicherheitVereinbarung über Bereitstellungsdienste
© 2000 Lumafield. All Rights Reserved.